赵德文
个性化签名
- 姓名:赵德文
- 目前身份:
- 担任导师情况:
- 学位:
-
学术头衔:
博士生导师,
- 职称:-
-
学科领域:
材料科学
- 研究兴趣:
赵德文,男,中共党员。1946年3月15日生,1970年东北大学金属压力加工专业本科毕业,后为东北大学金属加工系原理教研室助教。1978年考取该校塑性加工专业硕士研究生,1981年获硕士学位。后留校为讲师、副教授,现为轧制技术国家重点实验室、材料成形与控制工程系教授。
曾完成省自然科学基金项目“塑性加工力学近代数学解法研究”(负责人);“金属锻冲力组合数学解析技术研究”(负责人)。完成“厚板轧机坯料设计专家系统软件开发”(负责人),“60万千瓦大电机转子槽楔冷轧”(负责人),等省、部级科研项目及合同科研共12项;现承担国家自然科学基金“成形功率积分线性化方法及在金属加工中应用”(50474015),为负责人。国家十五‘863’项目- 500MPa碳素钢先进工业化制造技术的三级课题“超级钢热轧线材的研究开发”负责人。
曾获东北大学科研先进、教书育人先进若干次,获辽宁省省教委科技进步一等奖(1998)一项,辽宁省科技进步二等奖2项(1998、2000),国家科技进步二等奖一项(2001),辽宁省自然科学三等奖一项(2002)等奖励。
发表材料成形方面相关研究论文178篇(含会议论文),出版‘连续体成形力数学解法’,‘材料成形力学’、‘现代材料成形力学’各一部。培养硕士研究生若干名。
-
主页访问
2255
-
关注数
0
-
成果阅读
581
-
成果数
10
【期刊论文】Three Dimensional Analysis of Rolling by Twin Shear Stress Yielding Criterion
赵德文, ZHAO De-wen, XIE Ying-jie, LIU Xiang-hua, Wang Guo-dong
,-0001,():
-1年11月30日
By using the Twin Shear Stress Yielding Criterion and surface integral of the co-line vectors as well as integration depending on upper limit, Kobayashi three dimensional velocity field of rolling was analyzed and an analytical expression of roll toque and separating force obtained. Through redoing the same expe riment of rolling pure lead with Sims, the calculated results by above expression were compared with those of Kobayashi and Sims formulae. It turns out that Twin Shear Stress Yielding Criterion is available for rolling analysis and calculated results by the new formula are little higher than those by Kobayashi and Sims ones if reduction less than 30%.
Twin Shear Stress Yielding Criterion, co-line vector integral, three dimensional rolling, analytical solution
-
33浏览
-
0点赞
-
0收藏
-
0分享
-
139下载
-
0评论
-
引用
赵德文, 王哓文, 刘相华
应用科学学报,21(2):161-166,2003,-0001,():
-1年11月30日
本文对圆形平冲头轴对称冲入半无限体问题提出了参数方程建立速度场并以参量积分求解变形功率的新方法。得到了轴对称冲入应力状态因子的上界解析解。并证明该解略低于平面变形冲入三角形速度场的最小上界值。
轴对称冲入, 组合解析, 参数方程, 解析解
-
56浏览
-
0点赞
-
0收藏
-
0分享
-
87下载
-
0评论
-
引用
赵德文, 董学新, 刘相华, 王国栋
应用科学学报,20(2):2001,-0001,():
-1年11月30日
在大量现场测量与试验基础上修改了工厂原有坯料设计规则。将新规则成功编制成厚板生产坯料设计专家系统软件,经现场应用使年成材率提高1.61%,创造明显经济效益。
中厚板, 坯料设计, 专家系统软件, 成材率
-
74浏览
-
0点赞
-
0收藏
-
0分享
-
224下载
-
0评论
-
引用
【期刊论文】A Dodecagon Linear Yield Criterion with Optimal Approximation to Mises Criterion
赵德文, Dewen Zhao, Xiaowen Wang, Shizheng Wei, Xianghua Liu and Guodong Wang
钢铁,37(2):39-42,2002,-0001,():
-1年11月30日
On the π-plane in Haigh Westergaard stress space, the area of dodecagon intersected with Mises locus was taken to be equal to that of Mises, and the dodecagon was used as a new yield locus whose linear equation was derived in this paper. It has been proved that the dodecagon is the most approximate to the Mises locus among all dodecagons intersected with it. So the linear equation of the new locus was called the most approximate yield Criterion or MA Yield Criterion for short. In addition, plastic work rate done per unit volume of the new criterion and relation of k with s σ were also given out.
-
53浏览
-
0点赞
-
0收藏
-
0分享
-
338下载
-
0评论
-
引用
赵德文, 王磊, 刘相华, 王国栋
塑性工程学报,12(2):85-90,2005,-0001,():
-1年11月30日
提出了将能量泛函应变张量表示为应变矢量点积,而不采用Бунясовский 不等式放大被积函数的直接积分法,进而使被积函数转换为可积的线性组合函数并得到平面变形锻压矩形坯能量泛函的解析解。该解经实验与Tарновский 能量法、上界法及滑移线法解析结果及实测结果进行了比较。表明应变矢量分析结果低于Tарновский 数值结果和上界结果,与压力机实测指示的压力值误差为1.6 %。
泛函, 锻压, 应变矢量, 点积, 解析解
-
56浏览
-
0点赞
-
0收藏
-
0分享
-
86下载
-
0评论
-
引用
赵德文, 洪继要, 刘相华, 王国栋
东北大学学报,23(9):858-862,2002,-0001,():
-1年11月30日
以矢量分析法建立平冲头压入半无限体速度矢量场并证明其散度为零。由上界定理与待定参数法经参量与广义积分给出不同摩擦条件下冲头压力pr的通解。证明m=0时,通解最小上界值与Hill滑的移线解一致。给出不同摩擦条件p的最小上界值表达式及m与θ的关系式,定量分析了m对pr的影响。
矢量分析, 广义积分, 待定参数, 摩擦影响, 定量计算
-
61浏览
-
0点赞
-
0收藏
-
0分享
-
79下载
-
0评论
-
引用
【期刊论文】依赖Tresca和双剪应力屈服函数均值的屈服准则
赵德文, 刘相华, 王国栋
东北大学学报,23(10):976-981,2002,-0001,():
-1年11月30日
为使Mises屈服准则线性化,在Haigh Westergard应力空间,将Tresca与双剪应力屈服函数相加并取其平均屈服函数来作为新的屈服准则简称MY(平均屈服)准则,给出了该准则的数学表达式、屈服轨迹与单位体积塑性功率表达式。精度分析与算例表明:MY 准则是一个线性屈服准则,其与Mises 准则最大误差不超过3.9%,平均误差不超过1.95%,该准则的单位体积塑性功率表达式也是线性的。
平均屈服函数, Tresca准则,, 线性屈服, 屈服轨迹, 等边非等角十二边形, 单位体积塑性功率
-
82浏览
-
0点赞
-
0收藏
-
0分享
-
107下载
-
0评论
-
引用
【期刊论文】Tresca和双剪应力轨迹误差三角形中线确定的屈服方程
赵德文, 谢英杰, 刘相华, 王国栋
东北大学学报(自然科学版)24(11):2003,-0001,():
-1年11月30日
在π平面上,取Tresca与双剪应力屈服轨迹间误差三角形的几何中线确定新的屈服轨迹,建立了该轨迹在Haigh Westergard 应力空间上的应力方程,称此方程为几何中线屈服方程或简称GM屈服准则。证明了单位塑性功率表达式及其对Mises圆的逼近精度.精度分析与算例表明该准则与Mises准则的最大误差不超过2.9%,平均误差仅为0.95%,比MY(平均屈服)准则的逼近精度提高1%,且它是线性的,其轨迹为与Mises屈服轨迹相交的等边非等角十二边形.该准则的单位体积塑性功率表达式也是线性的.
Tresca准则, 双剪应力轨迹, 误差三角形, 几何中线, 等边非等角十二边形, 线性屈服准则
-
63浏览
-
0点赞
-
0收藏
-
0分享
-
108下载
-
0评论
-
引用
赵德文, Dewen ZHAO †, Yingjie XIE, Xiaowen WANG and Xianghua LIU
J . Mater. Sci. Technol., 21 (4): 433-437, 2005,-0001,():
-1年11月30日
In Haigh Westergaard stress space linear combination of Twin Shear Stress and Tresca yield functions is called the mean yield criterion or 'MY'Criterion for short. The mathematical relationship of the criterion and its plastic work rate done per unit volume are derived in present paper. A generalized worked example of slab forging is analyzed by the criterion and its corresponding plastic work rate done per unit volume. Then, the precision of the solution is compared with those by Mises and Twin Shear Stress yield criterions respectively. It turns out that the calculated results by MY criterion are in good agreement with those by Mises criterion.
Mean Yield criterion,, plastic work rate done per unit volume,, functional linearization,, Slab forging
-
42浏览
-
0点赞
-
0收藏
-
0分享
-
200下载
-
0评论
-
引用
【期刊论文】A Dodecagon Linear Yield Criterion with Optimal Approximation to Mises Criterion
赵德文, Dewen Zhao, Xiaowen Wang, Shizheng Wei, Xianghua Liu and Guodong Wang
,-0001,():
-1年11月30日
On the π-plane in Haigh Westergaard stress space, the area of dodecagon intersected with Mises locus was taken to be equal to that of Mises, and the dodecagon was used as a new yield locus whose linear equation was derived in this paper. It has been proved that the dodecagon is the most approximate to the Mises locus among all dodecagons intersected with it. So the linear equation of the new locus was called the most approximate yield Criterion or MA Yield Criterion for short. In addition, plastic work rate done per unit volume of the new criterion and relation of k with s σ were also given out.
-
61浏览
-
0点赞
-
0收藏
-
0分享
-
110下载
-
0评论
-
引用