已为您找到该学者16条结果 成果回收站
刘战强, 万熠, 艾兴
中国机械工程,2003,14(9):734~738,-0001,():
-1年11月30日
在高速铣削试验的基础上,研究高速切削时切削速度对切削力的影响。结果表明,在切削速度较低的情况下,切削力随切削转速的增加而增大,但达到某一临界速度后,随着切削速度继续增大,剪切角增大,造成切向切削分力下降。不同刀具材料与工件材料的匹配在不同切削条件下有不同的临界切削速度。
切削力, 高速切削, 铣削, 切削速度
-
104浏览
-
0点赞
-
0收藏
-
0分享
-
10655下载
-
0
-
引用
【期刊论文】Comment on 'Optimal grey-fuzzy controller design for a constant turning force system'
刘战强, By Shinn-Horng Chen, Jyh-Horng Chou and Jin-Jeng Li
International Journal of Machine Tools & Manufacture 42 (2002) 343-355,-0001,():
-1年11月30日
-
52浏览
-
0点赞
-
0收藏
-
0分享
-
123下载
-
0
-
引用
【期刊论文】Case representation and similarity in high-speed machining
刘战强, Zuntong Wang*, Zhanqiang Liu, Xing Ai
Z. Wang et al./International Journal of Machine Tools & Manufacture 43 (2003) 1347-1353,-0001,():
-1年11月30日
Applying case-based reasoning in high-speed machining can utilize previous cases and experience in machining a new work piece. This is helpful in overcoming the shortage of available high-speed machining data, and has significance for extending the application of HSM technology. For case representation, a model of case in HSM with relational data mode is proposed in the paper. With analysis of the characteristics of attributes and domain knowledge of HSM, the local similarities of case attributes are sorted into four classes: the numerical type, the enumerative type, the independent type, and the dependent type. The global similarity of cases is calculated by a composite similarity measure.
Similarity, Case-based reasoning, High-speed machining
-
75浏览
-
0点赞
-
0收藏
-
0分享
-
166下载
-
0
-
引用
【期刊论文】Wear patterns and mechanisms of cutting tools in high-speed face milling
刘战强, Z.Q. Liu*, X. Ai, H. Zhang, Z.T. Wang, Y. Wan
ZQ. Liu et al./Journal of Materials Processing Technology 129 (2002) 222-226,-0001,():
-1年11月30日
High-speed machining has received important interest because it leads to increase of productivity and a better workpieces surface quality. Holwever, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisems. In this paper, the wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grainde carbide tool in high-speed face milling are presentde when cutting cast iron, 45 temperde carbon steel and45 hardende carbonsteel. The tool wear patterns were examinde through a toolmaker's microscope. The research results show that the tool wear types differed in various matching of materials betweenthe cutting tool and the workpiece. The dominant wear pattrens observed were rake face wear, flank wear, chiping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion,diffusion and chemical wear promoted by cutting fores and high cutting temperature. Hence, the important considerations of high-speed cutting tool materials are high heat-reistance and wear-resistance, and chemical stability as well as resistance to the failure of coating. The research results will be of great benefit in the design and Science B.V. All rights reservde.
Cutting tool, Wear,, High-speed machining, Face milling
-
52浏览
-
0点赞
-
0收藏
-
0分享
-
164下载
-
0
-
引用
刘战强, Zhan-Qiang Liu and Patri K. Venuvinod
,-0001,():
-1年11月30日
Several hitherto unrealized advantages would follow if each shop floor machine could compile its own machining database autonomously. This paper focuses on CNC turning to develop a shop floor friendly method for determining the cutting force component normal to the machined surface as well as the lumped static stiffness parameters of the machining set up solely from onmachine part inspection data gathered immediately after machining. It is shown that one can also estimate the shear and chip flow angles as well as the tangential and feed forces by combining this method with a suitable predictive model of the turning operation.
-
64浏览
-
0点赞
-
1收藏
-
0分享
-
194下载
-
0
-
引用