Eu2 +,Dy3 + co-doped strontium aluminate (SrAl2O4) phosphor nanoparticles with high brightness and long afterglow were prepared by glycine-nitrate solution combustion synthesis at 500℃, followed by heating the resultant combustion ash at 1100℃ in a weak reductive atmosphere of active carbon. The average particle size of the SrAl2O4:Eu,Dy phosphor nanoparticles ranges from 15 to 45nm as indicated by transmission electron microscopy (TEM). The broad-band UV-excited luminescence of the SrAl2O4:Eu,Dy phosphor nanoparticles was observed at kmax=513nm due to transitions from the 4f65d1 to the 4f7 configuration of the Eu2+ion. The results indicated that the main peaks in the emission and excitation spectrum of phosphor nanoparticles shifted to the short wavelength compared with the phosphor obtained by the solid-state reaction synthesis method. The decay speed of the afterglow for phosphor nanoparticles was faster than that obtained by the solid-state reaction method.

Eu2+, Dy3+ co-doped strontium aluminate (SrAl2O4) phosphor nanometer powders with high brightness and long afterglow were prepared by heating the precursor gel (resulted from sol-gel method) at 900℃ and a reductive atmosphere of active carbon. The average particle size of the SrAl2O4:Eu, Dy phosphor powders was 59±7nm and its optical properties have been studied systematically. The broad band UV excited luminescence of the SrAl2O4: Eu, Dy was observed at λmax=506nm due to transitions from the 4f65d1 to the 4f7 configuration of the Eu2+ ion. The results indicated that the main peaks in the emission and excitation spectrum shifted to the short wavelength compared with phosphor obtained by the solid-state reaction synthesis method. The decay speed of the afterglow for nanometer phosphors was faster than that obtained by the solid-state reaction method.

A new analytical procedure for the direct determination of metal impurities (Cr, Cu, Fe and V) in aluminium oxide ceramic powders by slurry sampling fluorination assisted electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICPAES) is reported. A polytetrafluoroethylene (PTFE) emulsion was used as a fluorinating reagent to promote the vaporization of impurity elements in aluminium oxide ceramic powders from the graphite tube. A vaporization stage with a long ramp time and a short hold time provided the possibility of temporal analyte-matrix separation. The experimental results indicated that a 10μL1% m/v slurry of aluminium oxide could be destroyed and vaporized completely with 600μg PTFE under the selected conditions. Two aluminium oxide ceramic powder samples were used without any additional pretreatment. Analytical results obtained by using standard addition method with aqueous standard solution were checked by comparison of the results with pneumatic nebulization (PN)-ICP-AES based on the wet-chemical decomposition and analyte-matrix separation. The limits of detection (LODs) between 0.30μg g-1 (Fe ) and 0.08μgg-1 (Cu) were achieved, and, the repeatability of measurements was mainly better than 10%.

Cerium-doped mesoporous TiO2 nanoparticles with high surface area and thermal stable anatase wall were synthesized via hydrothermal process in a cetyltrimethylammonium bromide (CTAB)/Ti(SO4)2/Ce(NO3)4/H2O system. The obtained materials were characterized by XRD, FESEM, HRTEM, FTIR spectroscopy, nitrogen adsorption and DRS spectra. Experimental results indicated that the doping of cerium not only increased the surface area of mesoporous TiO2 nanoparticles, but also inhibited the mesopores collapse and the anatase-to-rutile phase transformation. Moreover, the undoped, doped anatase mesoporous nanoparticles exhibit higher photocatalytic activity than commercial photocatalyst (Degussa, P25), but the maximum photodegradation rate corresponds to the undoped mesoporous TiO2 nanoparticles. The lower photocatalytic activities of cerium-doped samples compared with undoped one may be ascribed to that the doped cerium partially blocks titania's surface sites available for the photodegradation and absorption of Rhodamine B (RB).

Mesoporous titania nanoparticles with high specific surface area and thermal stable anatasewallwas synthesized from surfactant laurylamine hydrochloride (LAHC) and inorganic precursor Ti(SO4)2. The as-synthesized and calcined materials were characterized by X-ray diffraction, nitrogen adsorption-desorption, transmission electron micrographs, Fourier transform infrared spectroscopy and thermogravimetric analysis. The obtained mesoporous TiO2 nanoparticles have mean diameter of 25.5 nm. The specific surface area of the mesoporous nanosized TiO2 calcined at 400℃ exceeded 189m2 g−1, and that of the samples after calcinations at 500℃ still have 151m2 g−1. The obtained anatase mesoporous TiO2 nanoparticles show relative high thermal stability.